Retour à la liste

Multi-rate 3G, Dual Output, Adaptive Cable Equalizer

Demande de rappel sur ce produit

Vous êtes intéressé par ce produit ? Laissez-nous vos coordonnées pour être recontacté par nos services.

Nom *

Prénom *

Société *

Code postal *

E-mail *

Téléphone *

* Veuillez remplir tous les champs obligatoires


Description

The GS2993 is a high-speed BiCMOS integrated circuit designed to equalize and restore signals received over 75ohm coaxial cable.

 The device is designed to support SMPTE 424M, SMPTE292M and SMPTE 259M, and is optimized for performance at 270Mb/s, 1.485Gb/s and 2.97Gb/s.

The GS2993 features DC restoration to compensate for the DC content of SMPTE pathological test patterns.

The Carrier Detect output pin (CD) indicates whether a valid input signal has been detected. It can be connected directly to the SLEEP pin to enable automatic power-down upon loss of carrier. A voltage programmable threshold, which can be changed via the SQ_ADJ pin, forces CD high when the input signal amplitude falls below the threshold. This allows the GS2993 to distinguish between low-amplitude SDI signals and noise at the input of the device.

The equalizing and DC restore stages are disengaged when the BYPASS pin is HIGH. No equalization occurs in Bypass mode.

The GS2993 includes a gain selection pin (GAIN_SEL) which, when tied HIGH, compensates for 6dB flat attenuation.The differential outputs can be DC-coupled to Gennum 3.3V cable drivers and reclockers and to industry-standard 1.2V, 2.5V and 3.3V CML logic.

The GS2993 also includes programmable de-emphasis with three operating levels in order to support long PCB traces.

The device is available in a 24-pin, 4mm x 4mm QFN package. Power consumption of the GS2993 is typically 210mW.

The GS2993 is Pb-free, and the encapsulation compound does not contain halogenated flame retardant.

This component and all homogeneous subcomponents are RoHS compliant.

Features


  • SMPTE 424M, SMPTE 292M and SMPTE 259M compliant
  • Automatic cable equalization
  • Multi-standard operation from 143Mb/s to 2.97Gb/s
  • Performance optimized for 270Mb/s, 1.485Gb/s and 2.97Gb/s. Typical equalized length of Belden 1694A cable:
    • 140m at 2.97Gb/s
    • 200m at 1.485Gb/s
    • 400m at 270Mb/s
  • Supports DVB-ASI at 270Mb/s
  • Dual, independently-controlled outputs
  • Manual bypass (useful for low data rates with slow rise/fall times)
  • Programmable carrier detect with squelch threshold adjustment
  • Automatic power-down on loss of signal
    • Standby power <30mW (typical)
  • Differential outputs support DC coupling to 1.2V, 2.5V and 3.3V CML logic
  • 0/6 dB gain boost selection pin
  • Cable Length Indicator output; varies monotonically with input cable length
  • Selectable de-emphasis: 2dB, 4dB and 6dB
  • Standard EIA/JEDEC logic control and status signal levels
  • Single 3.3V power supply operation
  • 210mW power consumption (typical)
  • Wide operating temperature range of -40ºC to +85ºC
  • Small footprint QFN package (4mm x 4mm)
  • Pb-free and RoHS compliant

Télécharger le(s) PDF(S)

Produits liés

Vous pourriez également être intéressé par les produits suivants :

Actualités

Les avantages des OLEDs sont connus: fort contraste, angle de vue, temps de réponse ultra-rapide, température d'utilisation étendue…
Mais les séries OLEDs d'Electronic Assembly sont capables de beaucoup plus

LA SURVEILLANCE DE LA QUALITÉ DE L’AIR, UN DÉFI? LE NOUVEAU CAPTEUR DE PARTICULES DE LA SÉRIE HPM D’HONEYWELL EST LÀ POUR VOUS AIDER

Fujitsu Components sélectionne Wirepas Mesh pour faciliter le développement de solutions IoT

The RDK-12GCONV UHD Converter Reference Design demonstrates the use of
Semtech's GS12241 12G UHD-SDI Re-timing Adaptive Equalizer, GS12090 Bidirectional
12G UHD-SDI Cable Equalizer/Driver, GS12281 12G UHD-SDI Re-timing Cable Driver,
and GS12070...

NEMEUS lance le Smart IoT Sensor compatible Arduino dédié à la réalisation de prototypes utilisant les technologies Sigfox®, LoRa®, Bluetooth® Low Energy, GPS/ GNSS

ACTUELLEMENT EN PROMOTION

Top