Retour à la liste

GS3441-INE3

Long Reach, Dual Output, Multi-rate 3G Adaptive Cable Equalizer

Demande de rappel sur ce produit

Vous êtes intéressé par ce produit ? Laissez-nous vos coordonnées pour être recontacté par nos services.

Nom *

Prénom *

Société *

Code postal *

E-mail *

Téléphone *

* Veuillez remplir tous les champs obligatoires


Description

The GS3441 is a high-speed BiCMOS integrated circuit designed to equalize and restore signals received over 75ohm coaxial cable.

The device is designed to support SMPTE ST 424, SMPTE ST 292 and SMPTE ST 259, and is optimized for performance at 270Mb/s, 1.485Gb/s and 2.97Gb/s.

The GS3441 features DC restoration to compensate for the DC content of SMPTE pathological test patterns.

 The Carrier Detect output pin (CD) indicates whether a valid input signal has been detected. It can be connected directly to the SLEEP pin to enable automatic power-down upon loss of carrier. A voltage programmable threshold, which can be changed via the SQ_ADJ pin, forces CD high when the input signal amplitude falls below the threshold.

This allows the GS3441 to distinguish between low-amplitude SDI signals and noise at the input of the device.

The equalizing and DC restore stages are disengaged when the BYPASS pin is HIGH. No equalization occurs in Bypass mode.

The GS3441 includes a gain selection pin (GAIN_SEL) which, when tied HIGH, compensates for 6dB flat attenuation.

The differential outputs can be DC-coupled to all Gennum cable drivers and reclockers and to industry-standard 1.2V, 2.5V and 3.3V CML logic using the OP_CTL pins.

The GS3441 also includes programmable de-emphasis with three operating levels in order to support long PCB traces. The device is available in a 24-pin, 4mm x 4mm QFN package.

The GS3441 is Pb-free, and the encapsulation compound does not contain halogenated flame retardant.

This component and all homogeneous subcomponents are RoHS compliant.

Features


  • SMPTE ST 424, SMPTE ST 292 and SMPTE ST 259 compliant
  • Automatic cable equalization
  • Multi-standard operation up to 2.97Gb/s
  • Performance optimized for 270Mb/s, 1.485Gb/s and 2.97Gb/s. Typical equalized length of Belden 1694A cable:
    • 200m at 2.97Gb/s
    • 220m at 1.485Gb/s
    • 400m at 270Mb/s
  • Supports DVB-ASI at 270Mb/s
  • Dual, independantly-controlled outputs
  • Manual bypass (useful for low data rates with slow rise/fall times)
  • Programmable carrier detect with squelch threshold adjustment
  • Automatic power-down on loss of signal
    • Standby power <30 mW (typical)
  • Differential outputs support DC coupling to 1.2V, 2.5V and 3.3V CML logic
  • 0/6 dB gain boost selection pin
  • Cable Length Indicator output; varies monotonically with input cable length
  • Selectable de-emphasis: 2dB, 4dB and 6dB
  • Standard EIA/JEDEC logic control and status signal levels
  • Wide operating temperature range of -40ºC to +85ºC
  • Small footprint QFN package (4mm x 4mm)
  • Pb-free and RoHS compliant

Télécharger le(s) PDF(S)

Produits liés

Vous pourriez également être intéressé par les produits suivants :

Actualités

L'équipe sourcing de Syscom-Prorep vous aide à gérer la pénurie de condensateurs.
Des millions de pièces Samsung Elmech en stock
Contactez-nous pour vérifier nos disponibilités

Jorjin Technologies propose un combo BLE 4.2 & Sigfox basé sur le chipset STM BlueNRG-1

Quectel propose le module EG25-G offrant une connectivité globale avec 30 bandes radio couvertes en LTE, 3G et 2G.
Basé sur le chipset Qualcomm MDM9x07 et suivant la release 11 LTE du 3GPP, le débit descendant atteint 150Mb/s et le débit montant...

Les avantages des OLEDs sont connus: fort contraste, angle de vue, temps de réponse ultra-rapide, température d'utilisation étendue…
Mais les séries OLEDs d'Electronic Assembly sont capables de beaucoup plus

Top